I know it’s still like 8000 degrees here in the South, but I’m already thinking ahead to the next season! This year, I want to be ready when the cold starts creeping in – even though you & I both know that won’t realistically happen here until, like, December (if not later!).

With that being said, I started this project WAY THE FUCK back in May – you know, when summer was the creeper. Took me this long to finish it, but whatever!

Prepare yourselves. This is a two-part project, so there are a bunch of pictures.

First part – the one I started in May (or was it April? omg.) is this sweet-ass track jacket hoodie combo! The pattern is the Augusta Hoodie from Named. I don’t tend to sew a lot of patterns from this company – I find most of the styles a bit outside of my personal style preferences (like the Inari dress that everyone is going apeshit over and I JUST CAN’T GET BEHIND THAT SORRY), but occasionally I’ll come across something that makes *me* go apeshit (see: my beloved Jamie Jeans LOVE U). As was the case with this jacket! The pattern was given to me as a gift by my lovely friend Carla; it has taken me over a year to decide what to make it up with, but I think it was worth the wait!

The Augusta Hoodie is a combo track jacket/hoodie with welt pockets, front snaps, and seaming that is perfect for some crazy colorblocking (even though I totally went the boring route). I made a size 32, and adjusted the sleeve length as I found them a bit long (a normal alteration for me).

Pattern construction wasn’t too terribly difficult – Named has gotten much better with their pattern instructions (they used to be quite sparse) and I had no problems with any of the steps, including the welt pocket. The jacket is unlined, but there is a facing so you get a nice clean edge at the front. The hood is lined, which I left off because my fabric was so thick. I also added a drawstring to the hood, cos I liked the way it looked. Ideally, I would have done this before finishing the hood – and used my machine to sew grommets around where the drawstring goes. Instead, I decided to do it after the hoodie was completely finished, and thus just popped a couple holes in the hood with my scissors and hoped for the best, ha.

The fabric is a super thick, super heavy cotton French Terry from Organic Cotton Plus. I went with the Cranberry color, although they have tons of other color options for French Terry. This fabric is amazingly thick and soft and will be wonderful to wear when the temperatures start dropping. The piped sleeve seams are done with strips of rib knit fabric, just flat – there is no piping in there (only cos I didn’t have any on hand and I didn’t feel like waiting for any to ship). The ribbing at the bottom and cuffs is actually two different kinds of fabric – I originally planned to use the aforementioned rib fabric from OCP, to keep everything consistent, but it was way way WAY too lightweight to work with this thick fabric. I ended up painstakingly ripping off the bottom band (which was serged on) and replacing it with a sturdy rib knit from Mood Fabrics, which holds up much better with the thick French terry. Of course, I fucked up my measurements and didn’t buy enough, so the cuffs is an entirely different rib knit that is a lighter weight (but heavier than the rib fabric from OCP). I don’t remember where that rib came from as it was in my stash, but I’m sure it was also from Mood. If you look closely, you can see that they are two slightly different shades of white, but I am choosing to ignore that. Also, rib is a weird word when you type it over and over. RIB.

Sewing with this fabric wasn’t necessarily difficult, but it did require some finesse because it is SO THICK. Cutting was kind of awful – my scissors are still pretty dull (yup, haven’t gotten them sharpened yet. How long have I been meaning to do this? 2 years?), and they didn’t have the easiest time chopping through all that thickness. It actually hurt my hand to cut through double layers, but also I am a huge baby. I sewed the majority of this on my serger – French Terry sheds like crazy, and serging helps keep that at minimum – and there were a few sections of massively thick layers where I had to coax the handwheel to get things to keep moving. My snaps are set using an industrial snap-setter – again, I have access to this from my old job (in sewing production) – I have NO idea how you’d set snaps in this otherwise! I guess the pattern calls for a lighter fabric, which would certainly be easier to work with. Overall, I wouldn’t say it was hard – it just required being slower and more patient. Which is infinitely easier when you are sewing something way the fuck out of season and know you won’t be able to wear it for months regardless

This track jacket reminds me of the stuff we used to wear back in the early 2000s, which I was still super active in the Nashville Hardcore scene. We were ALL ABOUT track jackets and hoodies, which looked real good with our tight jeans and Saucony Jazz shoes I definitely had a baby blue track jacket for years, which I loved everything about except that the fit was just a little boxier than what I wanted. So, here I am reverting back to my 16 year old self. Maybe should buy some Sauconys and relive the memories of the mosh pit or some shit.

Anywayyyy, after I finished the jacket, I realized I had enough French terry left over to make a pair of pants. Sweet! Like I said, this fabric is really thick and cushy, and I figured it would make a nice and warm pair of pants for lounging around the house.

I used the Anima Pants pattern from Papercut Patterns, sewn in a size XXS with about 2″ of length taken off. This was a very easy and straightforward pattern – basically just a knit pant with pockets, cuffs at the hem, and an elastic waistband with a drawstring. I did have minor troubles getting the elastic waistband sewn in – I think mostly due to fabric choice, as again, SO THICK OMG – but it’s fine, just a bit wonky looking. Whatever! For the white ribbing, I used a white cotton interlock knit, also from Organic Cotton Plus, which I so happened to have in my stash (the knits I used on the hoodie didn’t have enough yardage for these pants). It is leftover from these tshirts, btw. I can’t believe that shit was still hanging around my stash, but I ain’t gonna argue with that!

I am quite happy with how the pants fit, as well as how comfy and cozy they are. I am not especially happy to see that I have basically made an unintentional pair of Santa pants, but, it is what it is. I wasn’t planning on wearing these out of the house anyway (sorry, the whole ~athleisure~ trend is another thing I just cannot get behind), so I’m not terribly concerned about it. At least I have the perfect outfit to wear this Christmas.

(Btw, in case you were wondering – I also made my top. It’s a Papercut Patterns SJ Tee, sewn in a lightweight jersey fabric and cropped.

I should add, another thing I had no intention of doing was actually wearing these two pieces together.

Because I definitely look more like a late 90s Puff Daddy in this ensemble HAHA

I will let y’all know when my rap album drops, ok? Holler.

**Note: The French terry was given to me by Organic Cotton Plus, in exchange for a review. All rap opportunities are 100% my own.

Gah, it has been WAY too long since I made a pair of pants – according to my blog, that last pair was published in a February! LAME, TIME TO RECTIFY IMMEDIATELY.

Also, damn, my hair has gotten long since then. It seems to grow soo slowly until you look back and realize you’ve really gained some inches over the months, yay.

Anyway, Ginger Jeans! Again! I love this pattern so much, it’s definitely my pants TNT. The style is so classic, I can make a million pairs and have no one be the wiser that I’ve been wearing the same pattern for 6 months straight. I’m still tweaking the leg fit, but I really think the waist/hip fit is nailed down solid. And I love how it looks in different fabrics. While I primarily make this pattern up in denim, I’ve really wanted to try more colorful stretch twills. And here we are with that!

Sorry in advance for the terribly quality of these photos. Navy is almost as difficult to shoot as black, who would have thought!?

Anyway, I bought this navy stretch cotton twill from Mood Fabrics, back when I was in the NYC storefront in March – specifically with the intention of making myself some sweet pants out of the yardage. It’s a good stretch bottomweight for the kind of pants I like to wear – a lighter bottom weight (it’s still technically bottom weight, however, it’s about the lightest you can get away with – if that makes sense!) with a really good, solid amount of stretch. I have learned that I don’t like wearing really heavy fabric as pants – just don’t care at all for the way it feels. Maybe I’m sliding quickly into knit-fabrics-for-every-garment fabric territory, but I really like lightweight, super stretchy fabrics on my booty. Since that’s so freaking DIFFICULT to find with denim (get the right weight, and you lose out on recovery. Get the good recovery, and it’s like wearing raw denim in terms of stiffness, ew), cotton twill is where it’s AT. Bonus if that shit is colorful. I like colorful things.

This cotton twill seems to be a lot more along the lines of a cotton sateen, to be honest -it’s pretty shiny, for one. I rather like the effect – I think it looks a little more luxe than just a normal pair of pants – but as you can see, it highlights EVERY SINGLE wrinkle that shows up. It makes these pants look a lot more ill-fitting than they actually are… not that anyone would notice, except someone else who sews/fits, but it is what it is. I ain’t worried about it. Coupled with the fact that I like to wear my pants as skintight as if they are basically painted on, it’s pretty much wrinkle-city up in here. That’s ok, though. I will live.

I wanted to improve on the fit of my last pair – the full calf adjustment has been good in terms of allowing room for my calves and reducing the amount of knee wrinkles, however, I wasn’t happy with how wide the ankle ended up as a result. This is part of the reason why I’ve been reluctant to make this pattern again until now – that, and it’s been way too hot to wear pants for the past few months Anyway, I have that Ginger Jeans Intensive at Workroom Social this week, so I wanted to make the pattern before I left just to brush on the construction. Which meant that I also had to figure out the leg situation. Boo.

Ultimately, I figured that since the full calf adjustment was kind of the same concept as a full bust adjustment – i.e., you slash and spread to add width to a certain part of your pattern – then reducing the circumference of the ankle would basically be the opposite of that, like a small bust adjustment.

Here is my pattern piece after adding that extra room for my calves. As you can see, quite a bit of width was added at the ankle – 1 1/8″, to be exact. I wanted to reduce that amount without actually reducing the calf width, and also maintain the grainline of the pattern so the fabric wouldn’t twist and go all haywire (this is why you can’t just… shave down the side seams to remove the width. I tried that on the jeans with a basting stitch and it was just AWFUL. Did not work at all).

My Y-shaped slash and spread worked to add that width, so I did another Y-shaped slash right around where my calf starts to taper back into “normal width” category, using the super scientific method of holding the pattern piece up to my body and drawing wild lines on the paper with a pencil. (btw, that second slash line was my first try – and I realized it was way too low, so I taped it back together haha)

Instead of spreading, I overlapped the pieces together so that the original pattern paper (without my brown craft paper addition) butted up as normal right at the ankle. As you can see, it makes a very gradual curve to the side seams – they bellow out a little where the extra width is needed, and then gently curve back to their normal width tapering to nothing at the ankle. I also straightened the grainline, after I took the photo. Sorry bout that.

I had no idea if this was going to work – this is how I do my pattern adjustments (if I can’t find the answer in a book, anyway): mulling over the issue for a few months, doing some wild slashing that seems legit, and then cutting them off into shorts if it doesn’t work Fortunately, it worked! I still have the room I need for my calves, but the ankle is fitted as it should be. And I ended up with pants instead of having to cut them into shorts, so woohoo me:)

The only other change I made to these pants, in terms of construction, was how I applied the topstitching. I usually use topstitching thread – whether matching or in a contrast color – but I didn’t have any of that on hand when I made these pants (to be frank, I barely had ANY navy thread at all during this phase. I did have a bunch of bobbins filled with navy thread, which is what I used as my main thread hahaha AND MIRACULOUSLY HAD ENOUGH YAY). Instead, I used normal polyester thread – just whatever you’d use to, I dunno, assemble a garment – and set my machine to sew on the Triple Stitch. The Triple Stitch automatically lengthens your stitch just a few mm, and then sews over the same stitch a couple of times – which results in a nice, thick, dense stitch. It looks great for topstiching and solves the problem of not having the proper thread. I actually like it better than using topstitching thread, as you are less likely to get thread nests on the underside of your fabric! The only downside is that it is a giant ass bitch to unpick, so definitely be really really sure of what you’re sewing

Anyway, I used the Triple Stitch to topstitch all my seams – including the flat-felled seams. To keep my lines even and consistent, I used my edgestitching foot to get that 1/8″ from the seamline, and then my 1/4″ foot for the second pass. The bartacks are just teensy little zigzag/satin stitch blobs, using the same navy as the topstitching. I didn’t add any rivets or contrasty anything to these pants – I wanted them to be plain and a little sleek. The pocketing is the same striped cotton I use for pretty much all my pocketing – I bought a shitload of that yardage ages ago at Mood Fabrics, and it’s like the gift that keeps on giving forever haha I kept the longer length, just so these don’t end up being super high-waters after a couple of washes, but they look good cuffed, too

I have only had a chance to wear these once since finishing them, so I can’t 100% comment on the recovery of the stretch fabric – but at the end of the day on their inaugural wear, they stayed pretty tight and did not bag out. I’m interested to see how long they keep their shape before bagging happens, but so far so good, I think!

** Note: The fabrics used to make these pants were provided to me by Mood Fabrics, as part of my participation in the Mood Sewing Network. In case you were curious, the gingham for that shirt is also from Mood Fabrics it’s Butterick 5526 !

I have a well-documented love for the Ginger Jeans pattern. In fact, I love making (and wearing!) this pattern so much, that I just stopped posting about it. After you finish the 10th pair of pants, it just feeling way too fucking redundant to keep posting the same pattern praise over and over again. Needless to say, I have a lot of pairs of these pants, and more in the works for next winter. No shame about that, but also, no blog posts. You are welcome in advance.

With that being said, I loooove making pants and I found myself very intrigued with the Morgan Boyfriend Jeans pattern, which is also from Closet Case Patterns. I loved the idea of being able to make pants with a non-stretch fabric – truly, it opens up an enormous world of pants-possibilities that I hadn’t been able to consider in the past. Plus, I could keep making pants but pretend like they were like, totally different. Mostly, though, I wanted some non-stretch twill pants. I love the Organic Cotton Twill that Mood Fabrics sells (and yes, I’ve made pants with it before! And shorts!) and I know from experience that it’s a great fabric that wears and washes super well. I had about 1.5 yards leftover from my Organic Cotton Twill Kelly Anorak, so I decided to make the pattern as a sort of wearable muslin.

Truth be told, I actually got the Morgan Jeans pattern for Christmas last year. My little brother bought it for me (at my request) and while I was PUMPED to sew it up, it’s been languishing in my sewing room ever since. Every time I pulled it out of the envelope and tried to creep on the size chart, I just got overwhelmed and confused. I don’t know why this particular size chart buggered me out more than any other size chart in the history of ever – but that’s my excuse! See, I’m technically between sizes in Closet Case Patterns (I’m about 1/2″ bigger than the size 2, and a 1/2″ smaller than the 4). In my pants-making experience with this company, the size 2 fits pretty well, and the 4 is waaaay too big. However, this pattern suggests that you size up if you’re between sizes – and I kept having flashbacks of my size 4 Gingers that needed a LOT of tweaking to get a good fit, as they were just too big. I chatted with Heather about it when I saw her in DC, and she suggested going with the 2, so I took her advice and did just that.

Y’all, I’m so glad I had a moment of craziness and decided to trace my pattern – I generally DO NOT trace my patterns, but the sizing question was giving me major pause and I thought I would be pretty sad if I ended up cutting the wrong one. Which is exactly what I did, because the size 2 is definitely too small! Oh well, live and learn!

With that being said – these pants I am modeling are the original size 2 that I made, so I did make them work. I had to let out the leg seams (basically the side seams from as close to the waistband as I could get, all the way to about the knee area) as much as my seam allowances allowed (it’s hard to tell now since they’re all finished, but I didn’t cut any fabric off when I serged as I was anticipating this, so, I’d reckon those seam allowances are probably about 1/4″ now). They were still pretty tight, but fortunately, woven fabrics like this tend to ease and relax throughout the course of the day. TBH, I don’t think I can ever put these pants in the drier because I don’t want them to shrink back up! (A far cry from me in my early 20s – when I’d walk around the house pantsless all day and only put on my pants literally right before I left to party, so they’d be as tight as possible haha!) But with the seam allowances let out, and the fabric all relaxed and happy – the fit on these is pretty much perfect! So no complaints on this pair – and I’m so so happy I was able to salvage them, as shit got a little hairy for a minute there – but I definitely will need to size up to a 4 for my next pair.

Other than the sizing snafu, I am pretty pleased with the overall fit of these pants! I will be the first to admit that they may not be the most flattering thing I could put on my ass – but I think that’s kind of the case with a relaxed fit pant like this, regardless? And they are also a little tight, still, so sizing up on the next pair will probably help with that too.

I did not make any adjustments to the pattern – including not futzing with the rise. I usually shorten the rise as I have a bit of a short crotch, but I wanted to see how these fit out of the envelope. And again, I think it’s pretty good! Since they’re more of a relaxed fit than the tight Gingers, my calves fit in the legs just fine. FYI the inseam of these is pretty long – I think I measured it at about 32″ (I don’t know why that wasn’t included in the finished measurements, but there ya go), which is a good 4″ longer than what my lil’ legs require. Since the legs are straight, though, you can just cut off the excess length – which is what I did! These are hemmed to be a normal full-length, by the way, I just have them rolled for the pictures because that’s how I’ve been wearing them!

And speaking of wearing them – I took these photos on day 3 of wearing these pants, so they are pretty relaxed! And that also explains all the wear wrinkles. Whatever! It’s cotton, it’s gonna wrinkle!

My favorite part about making pants is all the fun detailing you get to play with! Topstitching, contrast bartacks, fun pockets – yes please!

For these, I used a darker olive all-purpose thread with the triple stitch (I think it looks nicer than using topstitching thread – although it is a BITCH to unpick, so be warned if you decide to go that route!), and brown thread for the bartacks. The pocket lining is a batik fat quarter that I bought at Loose Threads, a quilt shop that I stumbled upon at random while in Harriman, TN a few weeks ago for the Barkley Marathons. I was not actively seeking a fabric store (honestly, we were just looking for coffee), but I saw the words “Quilt Shop” and we had to make a quick detour. There isn’t much that I can buy in a quilt shop – still haven’t caught the quilting bug, ha! – but I can stash some fat quarters as they are the perfect size and weight for pocket linings!

I skipped the back pocket topstitching as I wanted to keep these reasonably plain, but added a leather back patch like the instructions suggest. This leather was pulled out of my box of leather scraps – I’m not entirely sure where it originally came from, but it’s fairly thick. I had used this same leather to make luggage tags for my suitcases (yes I am a big dork), and that square was a leftover piece from the center cut-out. Since my machine had no problem going through the 2 layers to make the tags, I knew it would be fine with a single layer + the cotton twill. I didn’t even change the needle for this – just went to town and it turned out fine.

Anyway, that’s all for now! Have you tried this pants pattern yet? What is your take on the boyfriend jeans (whether they are secretly made for females or you actually steal your *real* boyfriend’s jeans… tell me about that too)?

*Note: The main fabric used in this post was provided to me by Mood Fabrics, in exchange for my participation in the Mood Sewing Network.

Hi everyone! It’s been a wild two weeks over here… I turned 32, my mom got a hip replacement (she’s doing great!), and then I moved to a new house (which means NEW CRAFT ROOM coming soon!)! Lots of stuff going on, which meant less time for pretty much anything except packing and then unpacking. But I’m finally set up and settled in, and ready to get back to a more normal routine. This project is from last month’s Mood Sewing Network post, and I’m only just now getting around to having time to properly write about it – finally!

The most mind-boggling part about this post, I reckon, is that I MADE SOMETHING FOR SOMEONE ELSE. Clearly, that’s not me in these pictures! Although it’s my baby brother, so it’s bascially me with a beard haha. That being said, I rarely make anything for ANYONEEEE else, so this is a bit of a departure from my usual sewing. It’s been a long time since I’ve made something for a dude! Or anyone else for that matter haha.

My reasoning behind this project is pretty solid. Back around the holidays, I was wearing a reasonably new pair of Ginger jeans that I’d made for myself out of some really fabulous, really really really stretchy olive green twill. I love those pants and I’d still be wearing them right now if it wasn’t so damn hot outside! But I digress. Matt (little brother) noticed them and mentioned that he’s been looking for pants exactly like that for ages and he wished he had a pair, too. Now, Matt actually knows better than to ask me to make anything for him – he’s asked me millions of times and pretty much always gotten shot down – but I know he’s always wanted something handmade by me, his sister. His timing was good this time, though, as I’d just recently had the realization that while I loveeeeee sewing pants, I was kind of reaching a limit with what one person could reasonably wear during a season (I know I counted them, but I’m too scared to remember the exact number in my drawer. I think it was 19 D:). It was a good compromise, and I was in a good mood – so I agreed to make him his own pair.

Based on the style of pants he wanted, we decided on the Jedediah Pants from Thread Theory. I’ve never sewn with a pattern from this company – it’s primarily menswear, and remember, I don’t sew shit for no one else lolz – but I’ve followed them for ages and was excited to give them a spin! Rather than go by the sizing on the envelope, Matt supplied me with a pair of well-loved pants that had his perfect fit, and I used those measurements to choose his size. This ended up being a 32, although I think a 30 would have been better (but he is pleased with the fit, so whatevs! And don’t even get me started on the brain-bending behind making loose-fitting pants out of stretchy fabric. I don’t understand it, either!). I did not make any adjustments to the size or length – this is straight out of the envelope. I know they look short, but they are actually too long – Matt likes to wear weird socks and roll his pants to show them off, and we purposefully kept them long in case he ever wants to wear them to a more normal length. They can easily be re-hemmed!

The fabric is from Mood Fabrics, which I picked up when I was in NYC in March. I found the original olive fabric that I used for my pants there, and I was hoping there would still be some left when I came back. Unfortunately, that was not the case – but this one is fairly similar. It’s the exact same color (I actually wore my pants to the store to try to fabric-match, ha!) with about the same amount of stretch, but the fabric is quite a bit thicker. It’s almost spongey and there’s definitely a good amount of poly in it, as it doesn’t really press too well. Not my favorite fabric to work with, but doable!

As far as sewing the pattern, I only about half followed the instructions. I’ve made so many pairs of pants, I have a preferred order of steps and way of doing things. For example, I sewed the inseam before the side seams – this was for two reasons. One, it allowed me to flat-fell the inseam (Matt skateboards and he wears his clothes HARD, so they need to be as durable as possible), and two, I was able to baste the side seams and have him over for a quick fit before I finished everything and added the waistband. I also went my own way with the waistband insertion; I didn’t do that weird rolled thing that the instructions tell you to do (that shit makes absolutely no sense to me and if you’re confused, I can’t explain it. It’s witchcraft and I hate it haha), but instead just applied the waistband the same way you do for the Ginger jeans. I did opt to finish the facing edge with a length of bias, instead of turning it under, because it looks super cool on the inside now and that makes me happy.

Working with the fabric wasn’t terribly difficult, but like I mentioned, it didn’t really want to respond to pressing. I have found that with poly-rich fabrics – such as this one – it helps to use high heat and lots of steam (I have a shoe on my iron that protects my fabric – but if you don’t have a shoe, you’ll want to use a presscloth, else you gonna melt and/or scorch that shit), and then hold the pressed seam (or seam allowances) in place until they cool completely. One way to do this is with a clapper – or, if you hate waiting, you can do what I do and just pin them down. Easy and fast!

My favorite thing about making pants is all the fun ways you can customize them with topstitching – thread colors, designs, all that! Of course, Matt is a boring piece of shit and wanted NONE of that on his pants (jk ilu Matt)(but still, boring), boo! So we stuck with dark olive green thread – I used a single spool of all-purpose poly, and a triple stitch to get a nice thick topstitching line – and brown thread for the bartacks. The metal zipper and button are from the Garment District, from Sil Thread and Pacific Trimming, respectively.

I *was* able to have some fun with the inside! I used a plaid cotton that was in my stash (I think I got it from my Mamaw’s stash, actually haha) to line the pockets and add that bias trim around the edge of the waistband facing. It’s the same cotton that I used for the pocket bags of my olive pants, actually. Matt was actually pretty excited about how cool the insides look, which pleases me!

Because this is my little brother we are talking about, it was nearly impossible to have a normal photoshoot for these poor pants…

“Matt, smile or something.”

“Matt, turn around so I can get a photo of your butt.”

Anyway, Matt is thrilled with his new pants (in fact, the actual word he used was “stoked) and I’m happy that he’s happy! I hope he wears them until they fall apart – whether or not I make him a replacement pair, that is TBD. I think I’m all selfless-sewing’d out for the time being, ha!

Oh, and ladies, in case you were wondering… Matt is single

**Note: The main fabric used in this project was supplied to me by Mood Fabrics, in exchange for my monthly contribution to the Mood Sewing Network!

In case you forgot, I still really love making pants.

I’ve had to slow my roll a bit lately because I ended up with waaaay more pairs of pants that I can seriously, feasibly wear during the course of winter (I never wear pants in the summer – unless I’m on an airplane or in a movie theater, where it’s always fucking freezing – and I’m really impressed with people who can manage it. Too damn hot!), and I sorely missed sewing them. I can get a little bit of a fix when I run a Jeans Workshop, but it’s not the saaaaaame, you know?

Anyway, it appears I’ve gone up a size this year, so a lot of my old clothes don’t fit right. So, lucky me – I get to make new ones! Starting with pants, because, again, first love.

I’ve mentioned before that I’m a die hard when it comes to super tight, stretchy pants. I have loved that style ever since I first discovered it as a teenager (back when I learned how to use the sewing machine because I couldn’t find pants in that skinny cut – everything was flared at the time), and stuck with it over the decades. But I like branching out and trying new looks from time to time, such as this boyfriend jeans trend. The biggest upside to this look is that you don’t have to worry about stretch percentage when shopping for fabric – which is awesome and opens a whole WORLD of possibilities! Any fabric can be pants fabric if you put your mind to it!

This is my second go at the Morgan Boyfriend Jeans pattern from Closet Case Patterns (you can see my first pair, made of cotton twill, in this blog post). I re-traced the pattern to a size 4, since the size 2 I originally made was too small. These were still on the snug side when I first put them on, but thankfully the fabric has relaxed and I think the fit looks pretty good now.

The fabric! I actually used linen to make these – a beautiful marled gray-and-white bottomweight 100% linen that I picked up at my local fabric shop, Textile Fabrics, during one of their big sales. This was a huge remnant – I think I paid $20 for 3 yards. This fabric is usually around $20 for a single yard, so I definitely got a good price on this piece! It was pretty stiff when I first took it home, but after several washings it is thankfully starting to soften up. The fabric is not very thick – it’s more of a medium weight than a heavy weight – but it’s not see through, and it has enough of a heft that it doesn’t really wrinkle very much. In these photos, I have been wearing these pants for about 2 months – washed, machine dried and unironed. I’m really happy with the quality of this fabric, it’s really the perfect weight and thickness for a good pair of pants!

I also made my shirt, by the way! The pattern is the Sway Dress from Papercut Patterns, shortened to shirt length and sewn with a very lightweight raw silk that I bought in Egypt. I was 100% influenced by the Marlena Tank and wanted to make something similar. Mine is a lot more flared than the original inspiration- which is perfect in this drapey silk (seriously, I’ve never seen a raw silk this thin and drapey and omg I love it so much). I changed the construction of the top to mimic that of the Elizabeth Suzann – swapped out the facings for topstitched bias facings, and used French seams. I’ve probably sewn a thousand of those Marlena tanks, no lie, so putting this one together was like second nature (but not as fun on a non-industrial machine, ha!).

Anyway, back to my pants!

I had a lot of fun planning and sewing these! The black buttons are also from Textile Fabrics (and they were stupid expensive because they were ~imported from Italy~ ugh I mean come on), and the pocket lining is some black linen I had in my stash. I used black thread with a triple stitch for the topstitching, and thread bartacks in place of rivets. Rather than flat fell the seams, they are just serged and topstitched.

The back is my favorite part! I topstitched the pockets with some fun little swirlies, which I then mimicked on the leather waistband patch. It looks very designer to me. I’m a designer, you guys.

That’s all for this one! I will admit, I didn’t get to wear these as much as I had anticipated because it’s been soooo hot here, but they’ve finally had their place in the spotlight these past couple of weeks. I have the hems rolled up in these pictures, but I’ve been wearing them full length lately. They are hemmed slightly long; I wanted to make sure they were washed enough to get the shrink out before I hemmed them to the proper length. Seeing as I’ve washed and dried them probably a dozen times since finishing them, I should probably go ahead and re-hem. Maybe. Ha!

One last thing, I have ONE MORE jeans workshop for 2017, and it’s coming soooon!! I’ll be going back to Brooklyn to teach the Jeans Making Intensive in November and I can’t wait!

It just occurred to me yesterday that I never shared my Ginger Jeans that I made for my upcoming workshops! Fortunately, we had a weirdly sunny + 70° (look at how cool I am, I figured out the keyboard shortcut for making a degree sign lolz) day yesterday, so I jumped outside to take some photos! These aren’t the best – it was windy as hell, and for some reason I decided to take photos where I’d have to straddle over a fucking hole in the ground – but you know what, it works, and I’m moving on. I say this often, and it often bears repeating – no one comes to this blog for the stunning photography amirite.

Anyway.

These are my new jeans! I’ve made soooo many pairs of these Ginger Jeans that they don’t necessarily warrant their own post at this point (I mean, there are only so many times you can keep repeating the same pattern with no changes and expect people to find the information riveting haha), however, I did want to talk about this particular pair as I finally had a chance to make them in a new-to-me denim!

This denim is a super stretch denim from Robert Kaufman (FYI that’s an affiliate link). As I mentioned in my samples post, I chose this denim specifically because it was affordable, easy to source, and is great quality that is comparable to Cone Mills. I made all my workshop samples out of this denim – Robert Kaufman was generous enough to send me a couple bolts of the fabric; enough for 11 samples plus some extra so I could make a pair for myself! It’s an 8.6oz stretch denim, which is a hair lighter than most of the Cone Mills that people buy (I personally prefer the lighter weight, I find it more comfortable!). It’s also suuuuuper stretchy, which I love! Absolutely perfect for this jeans pattern.

Since this denim is indigo dyed, it is imperative that you prewash your fabric multiple times before cutting into it. It will shrink quite a bit, plus it bleeds a LOT! I only washed my samples once in cold water, and we all ended up with blue hands during class (true story; I went on a date immediately after the first night of my Nashville class and he totally called me out on that shit about halfway through haha). For these jeans, I washed + dried the denim three times before I cut it – twice with very hot water, and once with cold. This cut down significantly on the amount of bleed that I got, although they still bleed a tiny bit (not enough to damage, say, the upholstery in my car – but I do still notice a blue tint on my fingernails). Every single indigo-dyed denim I’ve used (especiallyyyy Cone Mills, oh god) does this, btw, but just be aware of it. Don’t carry a white purse, save your white undies for a different pair of pants, and for the love of god do not wash these in a load with anything but black fabric.

That being said, cutting down on the bleed does not actually fade the color. These are still super dark, even with all that hot washing.

Anyway, I made these a little over a month ago, and wore them on that first day of class so my students could see the ~jeans in action~. I’m happy to report that this fabric holds its shape really well – I’ve only washed these once since I made them (and even then it was mostly to try to bleed out more indigo, ha), and in these photos you are seeing them after about 4 days of wearing. No baggy knees or baggy butt! I still have a little bit of tightness at the calf, however, I have noticed with my more frequently-worn Gingers (i.e., the older ones) that over time the fabric will stretch and settle. I’m going to wear these a bit more and see if that happens with this fabric, before I slice up the calf and add more room on future pairs.

I also made the top I’m wearing, by the way! It’s a Grainline Studio Hemlock Tee (which is free if you join their newsletter). I used a beautiful striped rayon knit from Finch, which I bought when I was there last year for a workshop.

For these particular jeans, I used the same notions that we offer students in my workshops (copper topstiching thread, matching rivets and buttons). Combined with the fabric and pattern, you can literally see what your finished jeans will look like.

BTW, I still hate setting rivets. I’m getting better at it, but I still hate it. I considered getting a special die for my snap setter, but then I realized I couldn’t drag it along to workshops (that thing is cast iron and it weighs a LOT), so what’s the point? I generally prefer the look of bartacks over rivets, anyway.

I won’t go into detail about fitting these; but you can read my Ginger Jeans tag to see previous posts about what fitting changes I have made to these jeans over time. Spoiler: It took many, many pairs with lots of tiny changes (and I’m still making changes!). Fitting is a journey, and a lot of things just aren’t clear until you’ve worn your garment around for a few days.

Flat-felled seams on the inside, quilting cotton pockets (1-2 fat quarters is all you need!), and of course a shitty little thread nest in there #honestsewing

In other news – I just had some more classes listed! You can see all my upcoming classes here on my class page, but for those who are just browsing – here are the new ones added:

• March 24-25 / Jeans Making Intensive / Workroom Social, Brooklyn, NY (head’s up – we will be making a Workroom Social exclusive jeans pattern for this class! I am so excited about this one!)
• May 1-3 / Ginger Jeans Workshop / Stitch Sew Shop, Alexandria, VA
• July 13-15 / Ginger Jeans Workshop / Darrell Thomas Textiles, Ottawa, Ontario Canada
• July 18-20 / Ginger Jeans Workshop / Darrell Thomas Textiles, Ottawa, Ontario Canada
• August 3-5 / Master Class: Make Your Own Jeans Workshop / Pintuck & Purl, North Hampton, NH
• August 18-19 / Jeans Making Intensive / Workroom Social, Brooklyn, NY (again, this one is using a Workroom Social pattern )
• September 26-30 / Jeans & Wardrobe Basics Retreat / A Gathering of Stitches, Biddeford, ME (this one is a littttle different as we are focusing on wardrobe basics! There will be jeans-making, but there are also a couple extra days to make additional basics! Or, if you’ve already tackled jeans and wanted to try something else – such as a tshirt or button-up – bring it on!)

I have a few more classes in the works that haven’t been confirmed/listed yet (West Coast, I’m looking at you!), but I will share those as soon as I can! Other than that, pretty booked up for 2018! If you are a local shop who would like to discuss dates for 2019, please get in touch with me via email. If you are a person who wants me to come teach in your city, I encourage you to reach out to your local shop and tell them you’d like to see them host my jeans workshop

Ok, that’s all for this post! Happy Friday, y’all!

Well, y’all, it’s official – I’ve given up on sewing any more cold weather clothes for this season (although I still have a coat project that I haven’t shared – yet!! Keep an eye out for that one; I promise it’s worth the wait!!). It may still be spring here with some seriously flip-flopping temperatures, but I’m planning for the heat that I now is coming!

First up, some new pants! Yah, I have ENOUGH pants, we are all aware of that – seriously, my pants drawer is a bit much! – but most of what I have are jeans and skinny pants, better suited for cooler weather. When it’s warm outside, I need some space between my legs and my pants so that I can catch that breeze! I have a great pair of linen Florence pants from Elizabeth Suzann, which I love but could use some improvements to better match my needs (pockets + a flat non-elastic waist, plus a sliiiiightly lighter weight linen). I do love the shape of those Florence pants, though – the wide leg is perfect for a warm-but-not-quite-warm-enough-for-shorts day, the cropped length looks great with both flats and heels, and the high waist means I can wear them with cropped shirts.

With these changes in mind, I find the Lander pants from True Bias fits all those needs. I still have the high waist, cropped length, and wide leg, but with a slimmer fit through the thigh, a flat waistband (no elastic!) and pockets. I’m not the sort of person who thinks pockets should be in EVERYTHING, but I do like them in my pants! And while I respect that a slim pant can’t always have a pocket without adding additional bulk, this pattern does a fine job of giving me a place to stash my stuff without ruining the sleek style lines.

Pattern in hand, the next task was to find a good linen that fit my needs and preferences. I wanted something with a lighter medium weight – not as heavy as the Florence pants (they can get a bit warm when humidity rises), but with enough heft to still look ok as a bottom weight and not be as prone to wrinkles as a light weight. Not to mention, color is important! My Florences are navy, so I wanted to try for a different color (as much as I love navy, I don’t need two pairs of navy linen pants!). I reached out to my friends at The Confident Stitch for some ideas and swatches, and y’all, did they deliver! I decided to go with the Vivaldi Linen in red, which was exactly the weight + color I was hoping for (Vivaldi linen also comes in other colors – royal blue and taupe – if red ain’t your thing! They also have a great Brussels Washer Linen from Robert Kaufman that I considered, but ultimate decided it was a hair too light for the pants look I was going for).

I washed + dried my linen 3 times to get as much shrinkage out before cutting (I have been told this also helps with preventing wrinkles, which I can’t say for sure if that’s true, but this linen hasn’t been very prone to wrinkling!), using hot water and high heat. While the color did not bleed, it did turn my dryer lint bright red which sometimes got on my clothes (I just brushed it off, it didn’t stain anything. But it did make for a delightful dryer discovery). This Vivaldi linen was absolutely lovely to work with – it pressed and sewed without any trouble, had minimal fraying (I used my serger to finish all seams to further cut down on fray potential) and I didn’t have any issues with it shifting around during cutting. Just a great experience overall!

Before sewing up my pants, I made a muslin of the shorts version to see if I had any fitting adjustments to make. Based on my measurements, I started with a size 2 but they were pretty tight. Letting out the side seams about 1/2″ (the pattern includes 1″ seam allowance at the side seams for fitting) gave me a much better fit. I also took out about 1/4″ in the length of the crotch, fading to nothing at the side seams.

For the pair in red linen, I went up to a size 4. The overall width of the legs and length of the crotch is good, however, the center back needed to be taken in quite a bit to account for my hip to waist ratio (I think this pattern is cut for a more straight figure). This is an EASY adjustment to make; you just try on the pants before you add the waistband and take in the center back as needed for a closer fit. I took out an extra 3/4″, but honestly could have stood to remove more (I didn’t want to risk making them too tight at the waist – which I am guilty of doing, like, often, so I’m wearing them with a belt to cinch them in a little more). I almost removed another 1/4″ from the side seams, because my linen has more give than the muslin.

I cut the pockets for the size 4, but I think they are too big for my frame, especially after taking in that center back. There are two back pocket sizes for this pattern – a small pocket (sizes 0 & 2) and a slightly larger size (4 and up). In retrospect, I should have cut the smaller sizes, which I will do for the next pair. I just think they are slightly too big and a little overwhelming on me.

Finally, the length is the exact length called for in the pattern for the cropped version. I am a hair under 5’3″ so I wasn’t sure if they would be too long on me. I actually think they could stand to be shortened maybe 1″, but several people told me they are the perfect length (to me, they look almost like they accidentally shrank in the wash!). I am not going to mess with this pair, but next pair I may shorten them just a bit.

Construction-wise, this pattern is great. I’ve made DOZENS of pants at this point, so I’m not exactly a n00b to this, though. I had no problem following along for the steps, including the button fly. One thing I would change for the next pair is to interface the fly shield because it can definitely use that support, especially when sewn up with a linen.

What else? I used bemberg rayon (a scrap in my stash) to line the front pockets, and the buttons are from my local fabric store, Textile Fabrics. Took me foreeeeever to find a perfect matching red but I’m so glad I did! As a side note, these flat photos were taken after wearing the pants around for a full day, so you can see exactly how much the linen wrinkles (i.e., not much at all!).

So I think that’s all for this post + project! I’ve already worn these pants several times (as the weather allows) and have really loved that they provide a little warmth and coverage while still being light and breathable when the sun starts getting crazy. The high waist works great with a lot of my crop tops, which I’m excited to bust out!

Big thanks to The Confident Stitch for sponsoring this post and making my red linen pants dreams come true! As a side note, the links used in this post are affiliate links and will net me a percentage of any purchases you make through that site if you click the link (which in turn gets dumped directly back into my FABRIC FUND amirite woohoo). Thank you for supporting my blog, y’all!

Good morning, everyone!

In light of the official start to the OAL2018, I wanted to share a little tutorial for a very common pants adjustment – adjusting crotch depth. Even if you are not participating in the OAL, I hope you will find this useful! As I mentioned, this is a very common adjustment (at least half of my students in every Sew Your Own Jeans workshop that I teach ends up needing to make this adjustment!) that is a lot easier than it sounds.

This is the only pants-fitting post I’ll be doing for this OAL – most other adjustments can be done after the pants are basted at the side seams. If you have more pants-fitting needs, I absolutely recommend getting a copy of Pants for Real People (which is where the image below is from) – it is a fantastic resource that is full of valuable information and my top reference book when I’m fitting pants! Another post to check out is the Common Fitting Adjustments in the Lander Sewalong!

Common Pants Fit Adjustments – From Pants for Real People

So what does it mean to adjust crotch depth? The depth (versus the length, which runs from front waist to back waist) is the distance from your waist to the bottom of your crotch – i.e., the determining factor between a drop crotch and cameltoe. If you’ve ever had a wedgie, your depth is too short. Pants crotch hanging WAY lower than your actual crotch? Your depth is too long.

Since we are all special little sewing snowflakes (sewflakes?), all of our bodies are different – even in ways that aren’t super visible. Which means that not every single pants draft is going to fit every single person flawlessly – it’s just not possible. Personally, I have found that I have a slightly shorter crotch depth and generally need to make this adjustment with nearly every single pair of pants I sew. It’s not a hard adjustment to make, but if you’ve never seen is done before, it can be a little difficult to wrap your head around. Hopefully this tutorial will give you some insight on how to do it!

First, you’ll want to make a muslin of your pants (or at the very least – a shorts version of the pants). Sew the front and back as instructed. You don’t need to include the whole fly setup (unless you want to practice sewing it!) or waistband (unless you anticipate needing to change it to a curved waistband). Pin the fly shut and move around a bit. Don’t freak out over wrinkles – muslin wrinkles like crazy (mine are extra bad because I pulled these out of my rag pile, true story) and doesn’t have as much “give” as your regular fabric. Feel where the crotch is in relation to your body – is it hanging too low and causing extra folds due to excess length? Is it all up in your business and giving you cameltoe?

For a low-hanging crotch, pinch out the excess somewhere along the depth and pin it until it feels right. DO NOT OVERPIN – you don’t want to give yourself cameltoe (learn from my mistakes, people). Walk around, make sure you can sit, and let them settle a little. Likely, you won’t need to make a massive adjustment here – between 1/4″ – 1/2″ is most common. Little tiny fractions make a big difference when it comes to fit!

If your problem is the opposite and you need to add length, the easiest way to do this is to slice across the front of the pants and insert a strip of fabric (I just pin this, although you can sew it in, too). Pull down the bottom portion until the crotch feels like it is in the correct spot, then pin to the fabric strip.

I realize you likely cannot see a difference between those two photos (I mean… I definitely can’t haha). Like I said – it’s a small adjustment, and not always visible. But you can feel it!

Check the back to be sure there aren’t any depth adjustments needed. I’d say that maybe 1 out of every 15-20 students of mine need to actually adjust the back – it’s usually all in the front. If you do need to adjust the back, do so the same way you adjusted the front. Mine looks fine, so I left it as is.

Now take your muslin off, and measure the distance from pin to fold – or the additional length added by the strip of fabric. If you are only adjusting the front, then only measure at center front. If you are adjusting front + back, measure at the side as well as the center front and center back. This is how much you need to either add or remove from the depth.

Now how to translate this to your pattern? Easy! Your pattern piece should have a lengthen/shorten line that cuts across the fly (if it doesn’t – first of all, SHAME ON THAT PATTERNMAKER, but second, it’s easy to just add it somewhere in that general area nbd). If you are only shortening the front crotch, you will cut along that line from center front *just* to the side seam. Do not cut through the side seam – you want to leave a hinge. If you are also adjusting the back, cut straight across from edge to edge.

To lengthen, spread the pieces apart until the center front matches the measurement you took, and then fill the gap with paper and tape closed. If you are only lengthening the front, it should fade to nothing at the side seam.

To shorten, overlap the pieces until the center front is overlapped by the amount you measured. Again, if you are only adjusting the front, it should fade to nothing at the side seams/hinge.

If you need to adjust all the way around to the back, you’ll want to walk your pattern pieces to make sure that the side seams still match after making your adjustment.

Finally, redraw any wonky links or curves (such as the crotch curve if you overlapped – just smooth the curve) and straighten the grainline if necessary. You will also want to shorten or length your fly pieces (shield, facing, etc) the same amount so that they match up when you sew them together. I strongly advise making another muslin as this point to be sure that they changes didn’t wonk something up. You do you, though!

And that’s it! Like I said, a really easy adjustment that can make a world of difference in how your pants fit and feel. This is definitely the most common adjustment I see in my Sew Your Own Jeans workshops, so I wanted to share it here too!

Good morning, everyone! If you are participating in this year’s OAL, you should be rocking and rolling along with both your sewing & knitting projects. As I mentioned in the announcement, I will not be offering full tutorials for sewing the Lander Pants – there is a great sewalong available for free on the True Bias website, should you need the additional support – but I did want to pop in and share an alternate method for sewing the belt loops & attaching the waistband. Even if you are not participating in this year’s OAL, I hope you will find this useful!

You’ll want to make your belt loops before you attach the waistband (note that you can also attach the belt loops after the waistband if you prefer! For the sake of simplicity, I am following the pattern directions here). The pattern has you sew a tube that you turn right side out and press flat. This is a great method if you are sewing with a lightweight fabric, but it can be a nightmare to try to turn that skinny tube if you are using a heavier fabric, especially denim. Even my red linen doesn’t like being pulled like that! So here is an alternate method if you are using a thicker fabric, or just hate turning tubes

Finish one long edge of the belt loop piece. I used a serger, but you can also sew over the edge with a zigzag stitch, or bind with fabric.

The pattern is designed for the finished belt loops to be about 1/2″ wide. You may want to trim 1/8″ off the long (unfinished) edge of your piece if you want to maintain that measurement. Otherwise, your belt loops will end up being about 5/8″ wide.

Starting with the unfinished side, fold the belt loop into thirds with the right sides facing. You will end with the finished edge on top, hiding all raw edges. Be nitpicky here and do your best to get the finished edge right EXACTLY on top of the first fold.

Topstitch along both long sides at 1/8″. This is why it is so important to get the finished edge right on the fold – if you are too close to the center, the stitching line won’t catch it.

And that’s it! This gives the same effect as the turned-tube-belt-loop-, but I find it a lot easier to sew. From here, you can cut your belt loop into 5 pieces and attach them to the top of the pants as instructed.

Now, for the waistband!

If this tutorial seems like deja vu, it’s because I’ve showed it before on my blog! I wanted to show it again for those who missed it the first time, and also to show that it does work for one piece waistbands as well as two piece!

On your interfaced waistband piece, fold up one long edge a little bit less than the seam allowance (this pattern is 1/2″, so I folded up my edge at 3/8″) and press.

This is gonna seem ass-backwards – just bear with me! Attach the waistband to the INSIDE of the pants, with the right side of the waistband facing the wrong side of the pants. Sew all the way around at your normal seam allowance, making sure to leave at least 1/2″ overhang at each end (you can always cut off any excess). You will sew all the way around, from one opening to the other. If your pants have a zipper, make sure that it is unzipped and sew right across the zipper – just go slow so you don’t break your needle on the teeth.

Now you’ll fold the waistband back on itself, with the right sides facing. The side that has been folded and pressed – i.e., the side that was not sewn to the pants) should hang below by about 1/8″-1/16″. This is to ensure that the stitching line you just did will be covered when you turn the waistband right side out.

Now, stitch along the short edge, keeping in line with the center front edge of the pants. It may be helpful to draw a guideline here first with a ruler (which is exactly what I do – no shame here!).

Trim one of the seam allowance layers in half. Do not trim the corner, keep some seam allowance there.

Now you will turn the waistband right side out! To get a nice, crisp corner, start by sticking your thumb in the waistband up to the corner.

While your thumb is still in that corner, use your pointer finger to push the seam allowance down to one side (doesn’t matter which side) (Sorry, I don’t have pretty hands haha)

Keeping your fingers in that weird pinch, turn the waistband out to the right side.

You should end up with a nice sharp corner here! You can use a point turner to really push the edge out if you need it to be even sharper By holding the seam allowances in place when you turn right side out, this keeps the corner sharp (rather than trying to crap the seam allowances in after the fact). Keeping a bit of fabric in the seam allowances (rather than trimming down aggressively) also adds some structure to that corner, so it doesn’t collapse on itself.

Finally, you can pin the remainder of your waistband down and topstitch from the right side, making sure to cover the first stitching line. I like to start at the center back and go all the way around the long rectangle, ending where I started. You can then cover the backstitching with a belt loop

And that’s it! I love this method for attaching a waistband, because it ensures you get a beautiful, even topstitch on the outside without having to worry about catching the facing on the inside! It’s just EASY and basically fool-proof! You can also use this method for sewing in the round waistbands, cuffs (buttoned or in the round) and even collar stands.

Let me know if you have any questions!

I think I told y’all last year how much I love the new Geo Collection from Papercut Patterns. In case you missed it – I LOVE THE NEW GEO COLLECTION FROM PAPERCUT PATTERNS! As a shameless Papercut Fangirl, I am of course extremely biased regardless, but it is honestly a great collection. I’ve made the Pinnacle Top (twice, actually!), and the Fjord Cardigan (unblogged!), and now I’ve got some fresh new Palisade Pants to add to the mix!

I just think this pattern is so cool! I love the relaxed (but not oversized) shape, with the interesting pocket detail and elastic waist that doesn’t go all the way around (personally, I find a flat front to be more… well, flattering). These are very similar to the Elizabeth Suzann Clyde pants, with a different pocket shape and, again, a flat front with no elastic. Both pants have the same high waist and seams running down the front and back leg.

As much as I love a fitted pant, I didn’t want these to be too tight in the hip so I went with a size XS (based on my measurements). I ended up taking an additional 1/4″ out of the inseam to tighten up the legs ever so slightly (I don’t generally mess with the inseam, however, these pants do not have side seams), but I am very happy with how the hip and waist fits. FWIW, I did use the suggested elastic measurement and it fits perfectly without being too tight.

I made a muslin of the shorts before cutting into my fabric, because I wasn’t sure how these would fit on my body. I actually do own a pair of Clyde pants (from way back when I still worked at ES), and I always felt like the crotch was a little too long on me, so I went ahead and sewed up a test pair before committing. My test pair is actually a fully-finished wearable muslin – I used cotton bottomweight fabric, as well as the suggested interfacing, elastic, and topstitching details. So I also basically have a new pair of shorts when summer comes around haha. My sample showed that I did need to take some of the crotch length out – a full 1.5″ (crotch length refers to the measurement from front waist to back waist spanning the crotchal area, NOT the length from crotch to waist when you sit down, which is considered crotch depth. See this image for a visual) (also, every time I type crotch I accidentally type crochet instead what is wrong with me). Before you start wringing your hands on the mysteries of pants-fitting, please be aware that this is not an adjustment I see a lot of people make (and I touched a LOT of crotches last year during all my workshops). If you do need it, the explanation and process of how to fix are best outlined in Pants For Real People, which I recommend checking out for further questions!

ANYWAY, the amount that I took off the length was easily adjusted (albeit in a very hacky way) to my shorts, so yes, those are still wearable! One more adjustment I made to the pants was to change the crotch curve, as it was a little flat for my body (this is indicated by vertical folds in the fabric in a very unflattering spot). This was not necessary in my sample, but did show more prominently in my finished pants – probably because the fabric has more drape. The front still isn’t completely flat if I stand a certain way, but I think that’s pretty unavoidable with this soft fabric + pants shape combination.

Construction changes were minor. I wanted to keep the fabric soft, so I omitted about half of the interfacing (anywhere that there would be double layers of interfacing). This included the pockets and the center front waistband. In retrospect, I probably should have left the double layer of interfacing on the waistband as it does get a crease with wear, but, whatever. I used a lightweight fusible weft interfacing, which is pretty much my go-to for most fabrics.

I left off the mock fly (for aesthetic reasons), and just topstitched the center front and center back seams. I also added some topstitching to the back elastic, to keep it from twisting. And I also unintentionally shortened the pants when I shortened the crotch depth, so they are about 1.5″ shorter than the pattern – which thankfully is the perfect length for me haha.

My fabric is a gorgeous wool suiting that I bought from Mood Fabrics when I was in NY last month for Christmas. I only had one day in Manhattan, and my mom agreed to go with me while I did a quick little shop around the Garment District. Mood has tons of great wool suitings on their website, but I wanted to see the goods in person so I could get a nice feel for drape, weight, itchiness, and color. I knew I wanted something soft, lightweight, non-itchy (as I would not be lining these) and with a little bit of dimension and texture that didn’t look too suit-like. This stuff hit all those boxes, and only cost around $20/yard. It was wide, too, so the 2 yards I bought were more than enough for these pants – meaning I have leftovers to whip up something else if the mood strikes.

I actually pre-washed my wool – like, in the washing machine – because I wanted to see what would happen. Generally, wool felts due to heat combined with agitation, so I used cold water and low heat in the dryer. I didn’t measure before/after to see if anything shrunk, but this definitely isn’t felted so it worked out ok! When I wash the actual pants, I will use cold water in the washer and hang them to dry (how I treat most of my wool garments, except for handknit sweaters obviously).

The wool was really easy to sew, as wool tends to be. I suspect there is some poly blended in here, though, since it didn’t press as well as most wools do (this would also explain why the fabric was fine in the dryer when I pre-washed). I used high heat and a clapper to hold the seams down while they cooled, then for extra credit I topstitched as much as possible to keep the seams nice and flat. To sew, I used a universal 80/12 needle and finished all seams with my serger.

I think that about covers it! This was a fun project to make, and I really like how the pants turned out. I’m still undecided if these are really “me,” but I’ve worn them for the past 2 days while we’ve had a cold snap in Nashville and they are warm and comfortable. I do want to try this pattern with a fabric better suited for warmer weather – such as linen or tencel – and perhaps in a cropped length or even the shorts. The pocket detail just makes me so happy.

Oh! And in case you were curious – the shirt I am wearing is a mash-up of the Nikko Top and the Nettie Bodysuit. I basically just combined the bottom edge of the shirt with the lower half of the body suit, to make a Nikko Bodysuit. This piece has been really useful in my wardrobe – it looks great with high-waisted skirts and pants, and stays tucked in no matter which way I move. I made it with lightweight merino wool fabric, also from Mood Fabrics, and I love it so much!

**Note: The fabrics used in this post were provided to me by Mood Fabrics, in exchange for my participation in the Mood Sewing Network. All opinions are my own!

As someone who specializes in teaching Sew Your Own Jeans Weekend Workshops, I’m admittedly not the best at trying out new jeans patterns when they get released. Part of this is due to budget restraints (both monetary and in the sense of “ok Lauren just how many pairs of jeans do you really need?), part due to style choices (like, not gonna sew flared pants. I’m sorry. Maybe that will change in the future), and part is just because I know it’s a losing battle to try to keep up with everything as it gets released. That being said, I do enjoy seeing new things that are being released – especially when they cater to different styles and sizes! – and I’m especially receptive to anything that fulfills a personal style need in my own wardrobe.

I’ve been looking for a couple years now for a good non-stretch jeans pattern that will easily transition into shorts. Specifically, I wanted a shorts pattern that looked like – well, cut-off mom jeans. You know what I’m talking about – the super high waist, the tiny little back yoke, and the slight flare at the bottom of the leg. Bonus if the front pocket bags hang out! I’ve seen these all over the world – both in real life and on fashion blogs – and I haven’t found a sewing pattern that quite mimics it and is also readily available (i.e., not a vintage Calvin Klein pattern that costs $$$).

But, here they are! And I love them!

These are the Dawn Jeans from Megan Nielsen patterns – the mom jean pattern that I have been waiting for! With an ultra-high rise and four leg options (slim, straight, wide, and shorts), these are made with non-stretch denim and look like your classic jeans from the 70s/80s. They have all the features that make you think of jeans (including the option for a button or a zip fly) and a couple of different inseam choices so you can go long/tall, normal, or cropped. I loved this pattern as soon as it was released but it look me a little while to get around to making them. I’m glad I did though because this is definitely a new favorite for me!

I made the size 4, based on my hip and waist measurements, and chose the regular inseam (for the record, I am a little over 5’2″ and have a 28″-29″ inseam) and the slim leg. I find Megan Nielsen patterns to fit me pretty accurately right out of the envelope, so I threw caution to the wind and cut this shit straight out of my denim without making a test version first. There are NO adjustments to the pattern – this is exactly how it is drafted. Like I said, MN tends to work really well for me and you can see just how good they look! It’s like magic!

Also, I took a lot of photos so you’ll just have to suffer through them. Sorry.

My fabric is a medium weight Cone Mills denim that has been sitting my stash for probably about 3 years now. I’m sorry to say that I have absolutely no idea what weight it is, but it started out fairly rigid and has softened up with multiple washings. I like that it’s a medium blue color, instead of the dark wash that most shops carry. This was given to me by Jennifer at Workroom Social when I was up there to teach a workshop (again, a few years ago) so I’m not sure where it can be purchased now!

I had just enough to eek these jeans out (seriously, I think I had mere fumes of fabric left over by the time I was done cutting haha) and I’m so happy it worked out!

I used some quilting cotton that was in my stash to make the pocket bags. The topstitching thread is Mara 70, which is THE BEST topstitching thread imo. It is thick so you get the nice look of topstitching, but not as thick as the stuff that most fabric stores carry (which I find most home sewing machines don’t like at all). I keep loads of it in my stash and highly recommend all the shops I teach at to carry it for my workshops! If you have issues with topstitching thread in your machine, seriously, try this stuff! It’ll change your life! FYI the classic coppery color is #448

All other notions – the rivets, the button, even the leather back patch – are raided from my stash. This was a very economical make for me, ha!

For construction, I followed the directions rather than use my own methods. Most of it is pretty similar, although the fly construction is completely different. Many of sewing patterns (including Ginger) use a “fold-over” fly construction which is really simple to do (and SUPER simple to teach!) but not necessarily how it is sewn in ready to wear. The construction for this fly is where you sew the facing on (rather than it be cut with the front leg and folded back), which is the RTW method. This is also the method we use on the Claryville Jeans with Workroom Social (hopefully to be released soon!). It can be a bit confusing if you’re not used to it but it does admittedly have a nicer finish, I think! I found Megan’s directions to be pretty straight-forward and easy to decipher.

There are also instructions on how to make your own button hole (rather than use the automatic one on your machine), which I tried for this pair! Honestly, my machine doesn’t really have issues sewing button holes on any of my jeans but it was fun to try something different!

Overall, I am extremely happy with the fit and the general proportions of everything – I was initially a little concerned that the back pockets were too high, but after some wearing around + a very enthusiastic discussion on Instagram I have come to terms with my mom-butt. Since the fabric is non-stretch, it does start out quite tight (I wouldn’t say that it is necessarily uncomfortable, but it is restrictive especially in comparison to how stretch jeans feel!) but loosens up over the course of the day. These photos were taken after a couple of days wear, and you can see that they are still pretty slim-fitting.

My only beef with the pattern is the size of the front pockets. They are HUGE and super deep! I know people love having big pockets but these are unnecessarily giant – like, they go nearly halfway down my thigh. And since the pants are so tight, it’s not like you can really stash anything in them without it being super lumpy and/or uncomfortable. Because they are so deep, they are kind of useless – anything you put in them travels way over yonder and then is almost impossible to get out without doing some kind of weird pocket dance. I don’t use my front pockets much so this doesn’t super bother me for this pair, but I’ll be making them quite a bit more shallow on future pairs (except for my shorts, which obviously need some pockets hanging out of the front so I look like the hussy that I am).

Hm, what else? I guess that’s it! I’ve been holding these photos in my queue for a month or so now – as evidenced by the fact that they were taken in my old studio, and I moved about 3 weeks ago! My new yard is much more private (i.e., fenced, not on a corner lot, and I don’t have an upstairs neighbor who works from home all day!) so I am hoping I can get back to doing photos outside once I’m back in the States. In the meantime, I’m Vancouver-bound! See y’all laters!

Fun fact: I am wearing this same outfit as I type this blog post. Don’t be fooled, though, I took these photos months ago! I don’t know what my deal is, but for whatever reason I’ve become the sort of “blogger” (I am putting this in quotes because I think I’ve maybe written 6 posts this entire year lol) who takes photos and then… hoards them? Whatever.

Anyway, here’s a new pair of jeans to share! I think I’ve made enough pairs of Ginger Jeans to probably warrant never needing to post them again – students always ask me how many I think I’ve made, and the answer is I actually don’t know! I’ve lost count! – but I feel weirdly guilty about all the blog neglect this year, so I’m posting for the sake of posting something and keeping the ol’ stomping ground alive.

Also my hair looks really good in these photos, so there’s that. Gotta take those small victories wherever you find them!

Even though I’ve made tons of jeans, I recently reached a point in my wardrobe where I realized I was in pretty dire need of some wearable bottoms. My wardrobe goes through a lot of shifts and purges – things don’t turn out the way I envisioned, the fabric or fit is weird (let me tell you right now that no matter how much you sew or even use TNT patterns, you will never be immune to making these mistakes from time to time!), it’s a strange color or style I don’t actually wear, my weight has fluctuated and it doesn’t fit anymore, or I’ve worn them so much they are wearing out and need to be replaced. The last 2 reasons have really hit hard this year, when it came down to me owning 1 pair of (very poorly fitted) shorts and maybe 2 pairs of jeans. So I’ve been on a pants and shorts making binge which has been quite fruitful!

I used 3 different jeans patterns to really round out my pants wardrobe, so stay tuned for the other 2! Today, I want to talk about the Gingers!

If you’ve followed me for any amount of time, you probably know I have a mad love affair with this pattern. It’s one of my TNTs (tried’n’true), and like I said, I’ve sewn it so many times that I’ve literally lost count of how many pairs have passed through my sewing machine. I don’t know if it’s my favorite because it’s actually the best, or if it is just familiar. I do like the style and the fit works quite well for my body, though! It also helps that this is the pattern that I use for my Sew Your Own Jeans weekend workshops, so I feel like I truly know this pattern like I know the back of my hand.

I haven’t made this pattern since the end of 2017, and while I love that pair and still wear them regularly, I can see that they definitely have an end date – they are starting to wear very thin in some places, and the lycra is losing its elasticity. I think they still have quite a bit of life left to live, however, I think it’s always good to secure your back-up plan before it’s needed!

My fabric is a wonderful stretch denim that I purchased from Crafty Gemini back in August when I was in Florida for a sewing retreat. Usually whatever shop hosting my class will carry the specific denim that I recommend (this one from Robert Kaufman!), however, some shops like to source their own and that is also fine! In this case, Vanessa was able to get her hands on some very nice, dark indigo US-made stretch denim, which everyone in the retreat used. I was kind of jealous of how nice their pants were turning out so I decided to get a couple of yards for myself, too! This denim is just as stretchy as the RK, but a little heavier – maybe a 9 or 10oz. The color is nice and dark but I haven’t noticed as much dye rub-off as I tend to see with the RK denim.

I decided to go up a size in these jeans, which turned out to be a mistake. As I mentioned, my weight has gone up a bit this past year – mainly in my hips – so I’m sizing my new makes appropriately, and while I could squeeze into those 2’s if I really put my mind to it, I wanted some jeans that were a little less… painted on. Unfortunately, these ended up way too big so I should have just stuck with the 2’s! They look great now, but I did have to size down the side seams, and after taking these photos I also took in the waistband and center back a bit more. I think the issue is that 1. I’m exactly in between sizes with Closet Case Patterns (a little bigger than the 2, and a little smaller than the 4); and 2. My denim is very stretchy (about 25% stretch, the same as the Robert Kaufman that I usually use) which typically warrants sizing down, not up. Anyway, it was a fun experient and it all worked out in the end so I’m not mad about it, just making a mental note for next time!

Other than the sizing stuff, I did not make any other changes to this pattern. I added 1″ to the calf (ages and ages ago), but otherwise I get a pretty good fit out of the envelope, so that is nice and easy!

I did change the front pockets to be actual pockets, and not a pocket stay. I am fully aware that I am the minority in this thought process, but I HATE HATE HATE those pocket stays! I find them rigid, uncomfortable (which is all kinds of wrong when you’re wearing stretch denim, I mean wtf) and they make the fly area incredibly bulky. I know people loooove their pocket stays so please don’t @ me with your defense, just stating my personal choice here! Free-hanging pockets FTW! I have no issue tucking my pockets back in if it means I can eat a plate of nachos and not feel like I need to unbutton my pants! Fight me!

For some fun customization, I used contrasting thread to do my bar tacks, and stitched this cute little emoji patch on the butt pocket. Mostly because it makes me laugh, but also because I love any excuse to tell people I have “a heart on” lulz omg.

I also do not use the back pocket markings as suggested in the pattern, because in my experience they are too low and kind of unflattering! I think a high-waisted jean needs a high pocket, so I always place mine a little higher. In my Sew Your Own Jeans workshops, I custom place these on each booty (oh yeah I bet you didn’t know that fee included a nice hand down your pants!). For me when I’m sewing alone, though, it requires a lot of basting, trying on in the mirror, removing pants and unpicking stitches, rebasting, putting pants back on again, repeat ad nauseum. Fortunately I’m at a point where I have a general idea of where the pockets should be placed with just a good confident eyeballing, but my point is that you too can have good pocket placement, even if you don’t have the luxury of a second person to help you! Just be prepared to take your pants off a LOT and also maybe consider taking photos of your butt (why is this starting to sound like a Tinder conversation… ?).

I left the jeans unhemmed, because I’ve learned over the years that no matter how much you pre wash your denim (this one was 3x!), the length will continue to shrink in length over several more washes. I used to just hem my jeans on the long side, but these days I don’t bother hemming at all and just wear them rolled for a few months until I feel like they’ve gotten their shrink out. These are hemmed as of this posting, but were not as of the photographs.

Oh, I also made my top! It’s a True Bias Nikko Top, made with some really fun chartreuse knit that I bought at Fancy Tiger Crafts when I was there in June! I was very drawn to the color, but wasn’t sure how it would look on me – it took a lot of convincing from Bob, and then another few months of me staring at it on my shelf wondering if I had made a mistake. Honestly, though, I LOVE how it looks on me! I think it really works well with my skin tone and hair color, and it’s also a color that just makes me happy! So, Bob was right and I stand corrected!

Ok, I’m wrapping up this long-ass post with a photo of me + Amelia. Don’t be fooled by the bitchface, she loves me and was purring very loud during this photo haha.

Want to learn how to make your own jeans? Join me in 2020 and let me teach you how!

I’m back with another jeans post! Two down, one more to go!

This week, I want to focus on the Claryville Jeans, a pattern from Workroom Social.

The Claryville Jeans are a new release from Workroom Social, but hardly a new pattern – Jennifer has been working on it for at least a couple of years at this point! I actually sewed an earlier version of the pattern (before it was finalized), but I do like the small updates of the new one better! It was cool to be able to “work” with Jennifer on this pattern – I put that in quotes because she definitely did ALL of the work – I didn’t even test the pattern – but I offered lots and lots of opinions, both from an instructor perspective and as someone who has sewn a lot of jeans! Overall, I think the finished pattern is absolutely fabulous and I’m really proud of Jennifer for all the work she put into it to make it so great!

Anytime I mention this jeans pattern, the very first question I get (like, every single time lol) is “How does it compare to the Ginger Jeans pattern?” The short answer: It doesn’t. They are very different patterns, made to work with different types of denim, and fit in a different way on different bodies. You can’t really compare them, I’m sorry. What I can tell you is some of the key features of this pattern (this is all in the official description of the pattern, btw, which most companies should be including anyway!):
– BODY TYPE: This pattern is designed to fit a pear or hourglass shape; i.e., one with a large hip-to-waist ratio. If you are more straight/square, it probably won’t work for you without some adjustments.
– FIT: This is a mid-rise fit (right below the bellybutton), with a close fit through the hip and thigh, with a bit of extra room for the calf. It is a true jeans pattern, not necessarily “skinnies” or “jeggins” like the Gingers tend to veer toward.
– FABRIC: The Claryville uses denim with a very low stretch (I have heard rumors of people using non-stretch fabric to make this with great results, although I haven’t tried it myself), unlike the Gingers, which are stretch. You *can* make these in a stretch (just size down!), but the pattern is designed for low to no stretch.

Construction-wise, these go together like any other pair of jeans (although I will give a big shoutout to the 3/4″ side and inseam allowances which make fit tweaking SO MUCH EASIER!). The fly is constructed with multiple pieces (rather than a fold back fly like the Gingers), which definitely intimidates the shit out of my students when they first start the class, but honestly, it’s really easy and fun to do! TBH, I find it quite fool-proof and I think the instructions given are **far** easier than any other multi-piece fly instructions I’ve come across.

My favorite parts about this pattern are the small back yoke (so flattering!), the giant back pockets (there are 3 sizes to choose from, depending on the size of your butt! These are the small pockets), and the extra calf room (lord knows I need it). I also like that it uses a low-stretch fabric; it certainly is not as melt-on-the-couch comfortable as a good stretch denim, but they are quite nice regardless after a solid break-in. My pro tip for quickly breaking in your jeans: Wash them a LOT! I basically throw my jeans in the wash/dryer every single time something goes in there. After 5-10 washes they soften up considerably.

Fit-wise, these are great for me right out of the envelope. I made a size 2, with no adjustments other than length (these are 31″ inseam and mine is like… 28″ lol). The waistband is straight, and is supposed to be eased into the top of the pants which will naturally create a curve. In my workshops, we baste the inner waistband on first and check the fit, which is easy to adjust if you tend to get waistband gape.

I know someone is going to ask me about the denim I used, and here’s my answer: I know nothing about it! It’s from Workroom Social, the same denim that we use in the Jeans Intensive classes. I think it’s Japanese. There, now you know everything I know!

I kept these pretty simple as far as embellishments go, and used red for the bartacks and zipper, to match my pocket lining. The pocket lining is just a fat quarter, which is my FAVORITE fabric to use for pocket lining. It is sturdy, it is colorful, it is inexpensive and easy to source – what’s not to love? One thing I see a lot of students bring to class is cotton lawn (Liberty is especially popular for this) – my biggest advice is DO NOT DO THIS. Cotton lawn is very lightweight and not really suitable for a pocket bag. You will rip your pockets far before your jeans show even an inkling of wear. I cannot stress this enough.

My favorite part, though, is the back pockets! I had a stroke of a good idea earlier this year and decided to give them my initials It is subtle for sure – and really fun to hear people make the connection!

To do this, I drew the lines with chalk and a ruler, and stitched over them with topstitching thread. Easy!

I also snuck a little L on the coin pocket bartack, because why not?

Ok that’s all for these jeans! If you want to learn how to make the Claryville Jeans with me next year, you can sign up here at Workroom Social! Please be aware that my classes are in March, July, and November. There is a May class, but I am not instructing it Just FYI!

Alright y’all, I’m back with one more jeans post – the ~Designer Jeans~ Edition!

Thanks to Vogue 2442, I was able to make my own pair of Calvin Klein jeans

Before we get too far into the post, though, I just want to acknowledge how absolutely stupid this envelope cover is. You can barely see any of the details of the jeans (although the butt close-up is helpful, and to be completely transparent here, it’s a nice butt), and I don’t know why that woman is holding her leg up like that because you definitely can’t do it in these jeans. Nothing about this cover art (or lack thereof) makes me want to try this pattern, but nevertheless, I persevered. For science.

Anyway, here are mine!

I went down a little rabbit hole last fall while looking at vintage jeans. I reaaaaaally wanted some vintage Calvin Kleins, if only for the brag factor, but my budget currently doesn’t allow me to spend hundreds of dollars on someone’s used jeans (RIP, the vintage market). I considered sewing them, but recalled looking up vintage CK patterns years ago and they were going for obscene wads of money. Just out of curiosity, I checked again – and was surprised to see that there are plenty to choose from for $10-$20. Calvin Klein licensed his name to Vogue patterns a bunch throughout the 80s and 90s, occasionally offering a jeans pattern. There were loads of mom jeans to choose from (including a truly horrifying Vogue 2851, I mean, come on) but I went with the OG, the Vogue 2442 from 1980. In the effort of being as science-y as possible, I re-measured myself and chose the size that closely matched my measurements – in this case, the 8.

It took me a while to find a suitable denim to make these up – I wanted something non-stretch (as the pattern calls for – this was before stretch denim was really a thing!), but not too heavy, and a lighter wash. A bunch of the stuff I was coming up with ended up being way too lightweight, or had too much stretch, so this project ended up being shelved for longer than I would have liked.

As you can see, I did end up finding a great denim – from Art Gallery Fabrics, of all places! I’ll admit that Art Gallery Fabrics wouldn’t be my first thought when it comes to denim, but they’ve been expanding their denim gallery and I was curious to see what the offerings entailed. There is a great selection of lightweight (4.5oz, like what you’d use to make a button-down top or a sundress) denims, both printed and dyed various colors. The heavier denims clock in at 10oz (which is the lighter end of a pants-weight denim, and my personal preference), and come in a smaller selection of colors, nonstretch only.

After playing with some swatches, I chose the Crosshatch Textured Denim, in the Bubbling Brook colorway. My other choice was the Solid Textured Denim in Bluebottle Field, but that was sold out, so hopefully I can try it out in the future!

Anyway, about the Crosshatch Textured Denim! First off, you probably noticed that my jeans don’t exactly have a crosshatched design on them – that’s because you are looking at the wrong side of the fabric, baby! I actually don’t mind the crosshatch look, but upon receiving the fabric I fell in LURVE with the less contrasty wrong side of the fabric, so that’s what I went with on my jeans! My sewing project, my rules! The denim was pretty stiff and definitely not soft upon first receiving; but did get really soft and supple after just one wash. Be warned that it frays a lot, though – you’ll want to make sure you finish your seams (whether serging, or zigzaging, or even binding them) because otherwise the inside of your garment will get real hairy, real fast. If that bothers you, I mean. You do you.

Other than the fraying part, this denim was easy to work with. I recently got an Oliso Steam Iron (yes, the little iron that stands up when you stop touching it and yes it never ever stops being hilarious, no matter how much I use it) and this was my first real project to use it on. It doesn’t get quite as melt-your-hands-off-hot as my industrial gravity feed iron does (granted, this is cotton, so it doesn’t really need to be beaten into submission haha), but it heats up quickly, delivers a satisfying steam burst, doesn’t auto shut off every 2 minutes, oh, and IT STANDS ON IT’S OWN LITTLE FEET. My only regret in life is that I can’t find my stick-on googly eyes, because this iron needs eyeballs. Ok moving on.

So, more about the pattern itself! Like I said, I went with the size 8, which was based on my current measurements. I did not make any prior fitting adjustments or a muslin before cutting my fabric – I just went for it! I wanted to see what would happen! (this might be my new motto for 2020). Fit-wise, this was almost perfect right out of the envelope. I did end up making a few minor tweaks before I attached the waistband – because I am extra, and I like fiddling with things! – but if I hadn’t done anything at all these still would have absolutely been wearable.

Adjustments I made:
– Removed 1/2″ from the inner thighs, keeping the crotch length intact
– Scooped 1/8″ from the front crotch curve
– 5/8″ wedge at the center back yoke + waistband
– Cut 5″ total off the hem (I have a 28″ inseam, y’all lmao)

Sorry I didn’t take before photos, but these were all minor tweaks that didn’t translate very well in a photograph. Also, when I’m fitting, I don’t want to stop to take a bunch of weird ass selfies. Sorry, not sorry! Looking at these photos, I see I could have removed a little more from the inner thighs (as evidenced by the horizontal wrinkles pointing directly at my butt), but I can assure you this is a big improvement from the start, and I actually think they look worse in the photos than in real life! But, you know, it’s good enough. I spent far too much of my past sewing days overfitting myself to the point of frustration (and sometimes, actual discomfort). Nowadays, when I feel like I’m done fiddling with it, I just stop. As long as it’s not actually uncomfortable, I think it’s good enough! It has been very liberating and I encourage y’all to consider the same outlook

The instructions on this pattern certainly were interesting! As someone who’s made loads and loads (and loads) of jeans, these were a little more based on the home-sewer, rather than how RTW jeans are made (granted, I don’t have access to vintage jeans at this time, but the 1980s isn’t exactly the same type of vintage as, say, the 40s, and generally the construction methods back then were more similar to how they are now, i.e., serging seam allowances and such). As this is an older pattern, it wasn’t common for the average home sewist to have a serger – so the instructions include turning under edges, or finishing seams with a zigzag or overcast stitch. Interestingly, there is NO interfacing called for in this pattern (I interfaced the fly facing + outer waistband, out of habit and because I know that gets the me the result I like), but they do have you add twill tape to the top and bottom edges of the curved waistband to keep it from stretching out (that was a no from me, dawg). The other weird thing I noticed was that they have you double topstitch the side seams, and not the inseam. I also skipped that part (I prefer a stronger inseam, thnx) and did it my own way. However, I did follow the instructions for the most part.

The pattern includes a back pocket topstitching design, front pocket stays (pocket lining is also from Art Gallery Fabrics, fyi!), and a two-piece curved waistband. The pants are fitted at the waist, hips and thighs, and then the leg goes straight down (which is not what the line drawing suggests; they look a little more tapered on the envelope). Since my denim is such a light color, I opted for a pale brown topstitching thread (my beloved Gutterman Mara 70), rather than gold or copper. I alter a lot of jeans for clients and one thing I’ve noticed is that most jeans use brown thread, not gold or copper! My rivets and buttons are from the Garment District (I think these rivets might actually be for bags, but whatever, I like them); I had 1 extra rivet so I attached it to one corner of the back pocket. I saw this on a pair of jeans the stylist I work with was wearing, and while I normally hate rivets on back pockets, I thought it was kinda cute.

My only issue with this pattern is the two-piece curved waistband. Since it’s in two pieces, that means there a seam at the center back – great for fitting, but it also means a lot of bulk at the center back when the inner and outer waistband are sewn together (and then later, a belt loop is sewn on top of that). I also admit that I was running on fumes by the time the waistband facing was attached, so it’s not my best work. But, it’s on the inside, so who cares!

Overall, I enjoyed making this pattern and I think the finished jeans turned out great! I love the high waist (better for wearing crop tops with!), and the straight legs are a big style departure from my usual look. I love the lighter wash and subtle texture of the AGF denim, and I love love LOVE how soft it is! I don’t feel like I even really need to break these in, which is wonderful! If you’ve been looking for a good non-stretch, not-too-heavy denim, definitely check out what Art Gallery Fabrics has to offer!

** This post was sponsored by Oliso. All fabrics were provided by Art Gallery Fabrics. As always – all thoughts, opinions, and weird ideas are my own! **

It’s been a minute since I shared a knitting project! I actually *have* been knitting – I always have at least 1 project on my needles at any given time (usually two – one for the couch, and a smaller/simpler one for the road!), and I always keep my Ravelry account updated! But for whatever reason, I never feel super compelled to share them on my blog. Anyway, here’s one today!

This is the Tongue Tied sweater by Poison Grrls. I actually chose the yarn before the sweater pattern – a very uncharacteristic knitting move for me (usually I have my pattern selected before I start shopping for yarn). To be completely honest – I wasn’t in the mindset for planning a new sweater when all this happened, as I was still steadily working my way through my last sweater (see! There’s one I knit and never shared here lmao). But this yarn caught my eye at Pintuck & Purl and once I got my hands on it, it was all I could think about.

The yarn is CashLuxe Spark by Sweet Georgia Yarns, a gloriously soft and cushiony fingering-weight yarn with this incredibly rich color and the cutest subtle sparkle! I’m not a super duper yarn snob (I love natural fibers, blah blah, but I don’t typically buy *really* expensive yarn. Although. That may now change haha) but I really, really, really wanted this yarn on my body. I initially considered socks – I mean, who doesn’t want to wrap their toes in cashmere? – but at $38/skein, that was a little rich even for my blood. So obviously it made sense to buy two skeins and turn it into a sweater, because that’s totally fiscally responsible.

I started this sweater right after I finished my last one, toward the end of December last year. It knitted up really fast – partially because, well, it’s a tiny fucking sweater, but also I just really enjoyed every part of the process. I LOVED touching that yarn, so so much. I actually would have finished this quite a bit sooner, except once I got to the point of picking up the sleeves I let it sit dormant for a couple of weeks while I worked on other stuff.

Not a lot to say about this pattern, but here are some notes:
– I knit the size Small, based on my bust measurement. My gauge called for size 2 needles (body) and 1 needles (ribbing).
– This is a really fitted sweater! I mean, I knew that going in – but trying it on, yeah, it’s basically painted on. Aggressively blocking the entire thing really well helped a lot, and now it skims my body perfectly.
– Because it was so tight, I did have some issues with getting a stretchy enough bind off (I actually had to re-do my bind off at the bottom AND the neckline twice!). I ended up using size 3 needles and a super stretchy bind off. With the neckline, that was mainly my fault for being an idiot. I thought I’d be super clever and do a fold-over neckband, but quickly discovered (while unsuccessfully trying to pull it over my head) that those don’t stretch at all. LMAO.
– Mod-wise, I added 1″ of length to the body, since I wanted to be able to wear this with high-waisted jeans (it’s pretty short!).
– If you think you see a yarn tail in the back, you’re right. I haven’t woven it in yet. I don’t know why.

I loved knitting this pattern! It was easy to follow, simple to knit (but not boring), and the proportions are just lovely. I’ve already got a few more Poison Grrls patterns in my radar for my next sweater. I love Amy’s aesthetic and I love that she uses fingering weight yarn – perfect for our mild winters!

Oh, I also made my pants, too! These are more Dawn Jeans, made in Robert Kaufman non-stretch corduroy from Pintuck & Purl! (I picked it out the same time I was fantasizing about that yarn haha). Not much to say about these that I haven’t already said – I made my normal size, this time with the wide legs and the cropped length. The cropped length isn’t actually that cropped – I ended up having to take off another 3″ or so (but I also have a 28″ inseam sooo take that as you will). I’m also not super thrilled about how the back fits, but I believe that’s just what you get with wide leg pants. The wrinkles are there because there is too much fabric at the inner thigh (the issue I had with my Calvin Klein jeans), but for true wide-leg pants you really don’t want to remove width there. Whatever, I’m not the one looking at my own butt so I don’t care.

So anyway, that’s my new sweater! Fun to knit, fun to wear, and the sparkles make me happy Oh! And I still have some of this yarn leftover – so you better believe I’ll be making a tiny pair of socks If anyone has suggestions for short-cuff sock patterns – preferably one with bobbles (I don’t know why but I’m feeling like I want bobbles on these), let me know!

Look y’all, new jeans!

I always enjoy making a new pair of jeans for fall – after a summer of teaching jeans-making, I’m full of brilliant ideas and antsy to sew them. Now that I work part time as a tailor, I get my eyes on even more jeans with interesting design details that I’ve been dying to incorporate. For this pair, I thought I’d try out some features I’ve been seeing a lot lately, as well as a new (fashionable?) silhouette .

These are my tried and true jeans pattern – the Ginger Jeans from Closet Core Patterns. I’ve made this pattern enough times to have really nailed the fit down, and now I’m in that glorious phase where I just have to make tweaks and adjustments to change the style. I made multiple changes to this pattern:

• Increased the rise about about 3/4″, so it covers my belly button
• Changed the legs to bootcut, using an existing pair of flared jeans that I like as a comparison
• Swapped the pocket stay for normal hanging pocket bags
• Changed the waistband to a rectangular one-piece folded waistband, instead of two pieces with subtle shaping. The shaping is obtained by easing the waistband to the top of the jeans. This is how most RTW jeans are done, btw, and it is MUCH easier to cut, sew, and alter

I also made some small design adjustments, such as leaving off the coin pocket, slightly changing the shape of the front fly topstitching, and sewing 2 lines of topstitching across the bottom of the waistband. I also used two different topstitch thread colors, as well as a third color for the bar tacks and button hole.

Not too much to say here that I haven’t already said before about this pattern, so here’s a bunch of photos of me + my ass.

I have no idea where I originally purchased my denim – if I had to guess, it’s either from Mood Fabrics or Pintuck & Purl, as I’ve bought loads of stashed denim from those sources. Maybe it’s Cone Mills? Who knows, it’s a mystery! All I can tell you is that it’s been in my stash for years. It is a beautiful medium blue that I think will lighten up nicely as it gets washed and worn. 4″ of my denim stretches to about 4.75″, so I was able to cut my usual size 4 and make no fit or size adjustments.

I used two sewing machines to sew this – one threaded for topstitch thread, and one for standard. Although I still had to change my thread a ton, since I was using two different topstitch colors! But I do think the effect is worth it, I see this in a lot of high-end RTW and I just think it looks really nice. I used Mara 30 topstitching thread, which is pretty thick – honestly too thick for most home sewing machines. I have a Janome HD9 that I use for topstitching, which is designed to be able to handle the super thick thread with a 110 needle. In my classes, we use the thinner Mara 70, which gives the look of thick topstitching but much more easily managed by the machines.

Love that you can’t even tell the difference between the two thread colors in this eXtReMe cLoSe Up BUT I PROMISE IT IS THERE.

I used a leftover scrap of Liberty cotton to make the pocket bags, which I sort of regret because it’s way too flimsy and doesn’t stay in place that great but oh well the colors were just too good! My serging thread is green to match. Oh, and I found an old Ralph Lauren label that I was able to fold so my pants have my name in them! Fun stuff!

I love the little flare – it’s very different than anything else in my closet (well, other than the *other* pair of flares I own that I knocked off LOL). The length is definitely long for me, but in my experience denim tends to continue to shrink in length as you wash/dry it so I’m going to let these settle a bit before I cut anything off. Plus, longer hems are supposed to be in right now? I don’t know, I keep looking at everyone’s long ass pants and thinking about how much they need a good hemming haha.

This was a fun little project and a great way to ease back into sewing after a summer of barely having time to make anything for myself! If you’re keen to whip up your own jeans, I still have a few classes through the end of the year – check out my WORKSHOPS page to get the details! We won’t have time in class to go fully custom – but you’ll learn everything you need to know about making a pair of jeans from start to finish, and get lots of ideas for customization on your future pairs! Also, as a head’s up – I’m currently planning my schedule for 2024 (with the possibility of adding a new location or two), so if you have a local shop offering classes who you’d like to nominate, please let me know!